Arduino with wifi module

Getting started with the Arduino Uno WiFi Rev2

The Arduino Uno WiFi Rev2 is an Arduino Uno with an integrated WiFi module. The board is based on the Microchip MEGA4809 with an ESP32 u-blox NINA-W13 WiFi Module integrated. The NINA-W13 Module is a self contained SoC with integrated TCP/IP protocol stack that can give access to your WiFi network (or the device can act as an access point).

The Arduino Uno WiFi Rev2 is programmed using the Arduino Software (IDE), our Integrated Development Environment common to all our boards and running both online and offline. For more information on how to get started with the Arduino Software visit the Getting Started page.

Use your Arduino Uno WiFi Rev2 on the Arduino Web IDE

All Arduino boards, including this one, work out-of-the-box on the Arduino Web Editor, you only need to install Arduino Create Agent to get started.

The Arduino Web Editor is hosted online, therefore it will always be up-to-date with the latest features and support for all boards. Follow this simple guide to start coding on the browser and upload your sketches onto your board.

Use your Arduino Uno WiFi Rev2 on the Arduino Desktop IDE

If you want to program your Arduino Uno WiFi Rev2 while offline you need to install the Arduino Desktop IDE. Full instructions on how to install it can be found in our Getting Started page.

You will need to add the Arduino megaAVR Core to the Arduino IDE. This simple procedure is done selecting Tools menu, then Boards and last Boards Manager, as documented in the Arduino Boards Manager page.

Installing Drivers for the Uno WiFi

macOS No drivers are needed for the Arduino UNO WiFi Rev2 on macOS.

Windows (tested on XP, 7, Vista and 10) At this point of this Getting Started guide you already have installed the drivers together with the Arduino Software (IDE) and the board will be recognized automatically.

Linux There is no need to install drivers for Ubuntu 10.0.4 and later, but make sure port 5353 is not being blocked by a firewall. Users with Linux need to run this code in the terminal: ~/.arduino15/packages/arduino/hardware/megaavr/1.8.1/scripts/create_dfu_udev_rule

You need to be admin on the computer to do so.

Open your first sketch

Open the LED blink example sketch: File > Examples >01.Basics > Blink.

Select your board type and port

You’ll need to select the entry in the Tools > Board menu that corresponds to your Arduino Uno WiFi Rev2 board.

Select the serial device of the board from the Tools | Serial Port menu. This is likely to be COM3 or higher (COM1 and COM2 are usually reserved for hardware serial ports). To find out, you can disconnect your board and re-open the menu; the entry that disappears should be the Arduino Uno WiFi Rev2 board. Reconnect the board and select that serial port.

Upload the program

Now, simply click the «Upload» button in the environment.

Wait a few seconds — you should see the green progress bar on the right of the status bar. If the upload is successful, the message «Done uploading.» will appear on the left in the status bar.

A few seconds after the upload finishes, you should see the on-board LED start to blink. If it does, congratulations! You’ve gotten your Uno WiFi board up-and-running for the USB programming. If you have problems, please see the troubleshooting suggestions.

Tutorials

Now that you have set up and programmed your Uno WiFi board, you may find inspiration in our Project Hub tutorial platform, or have a look to the tutorial pages that explain how to use the various features of your board. We suggest that you visit the WiFi Nina Library page that explains the network functions of this board.

Please Read.

This board uses the new Microchip MEGA4809 microcontroller that has a different memory layout compared to the usual ATmega 328P. You now have 48K of Flash memory, 6K of RAM and 256 bytes of EEPROM, therefore you have more Flash and more memory than the Arduino UNO (16K Flash and 2K RAM). The programming of the MEGA4809 happens through an ATmega 32U4 programmed with the mDBG code and creates a virtual COM port when connected to a PC.

Serial ports

The Arduino Uno WiFi Rev. 2 has 3 hardware serial ports. Serial is connected to the USB interface, Serial1 is connected to Pin 0 (RX) and 1 (TX), Serial 2 is connected to the u-blox NINA-W13 module. This allows the usage of pins 0 and 1 without issues: on the original Arduino UNO, the usage of Pins 0 and 1 disrupts the sketch upload.

SPI

The SPI interface is available on the ICSP connector with the usual layout for MISO, MOSI, SCK and CS. The IMU and the WiFi module are connected to the SPI bus and have individuale and dedicated pins for Chip Select (CS)

I2C

The I2C interface is available on the SDA and SCL pins. Unlike the classic Arduino Uno, these pins are not alternatives to pins A4 and A5. This means you are still free to use the Uno WiFi Rev2’s A4 and A5 for anything you like when an I2C device is connected to SDA and SCL.

Analog

The new core has 5 PWM pins and the pin 11 doesn’t support PWM. The resolution of the 6 A/D pins is the usual, with 10 bits and values from 0 to 1023.

RGB LED

Close to the Nina module and the ICSP connector there is a square RGB SMD LED. This LED is directly connected to the NINA-W13 WiFi module and it is driven by the module itself. It will be used for future applications and developments.

Integrated IMU

On the SPI bus, with a dedicated CS connection (pin D30 or SPIIMU_SS) and a dedicated interrupt pin (SPIIMU_INT), the Arduino UNO WiFi Rev.2 has a LSM6DS IMU with 3-axis accelerometer and 3-axis gyroscope. This chip, made by ST Microelectronics, is a standard component that you can use with our own library Arduino_LSM6DS3. To get the library, you can use our Library Manager available in the Arduino Software (IDE) .

The library contains two examples to show you how to read acceleration and rotational speed.

Interrupts

The new MEGA4809 microcontroller allows you to attach any digital pin to an interrupt, therefore you may have as many Interrupt Service Routines (ISR) as the available digital pins. You still define the interrupts with the usual function attachInterrupt(digitalPinToInterrupt(pin), ISR, mode); . Please refer to the attachInterrupt() page for further details.

Note: the WiFi antenna built in in the U-blox NINA-W13 module is made for embedded products and should NOT be touched. Applying pressure or force on it could cause damage. Be very careful when you detach shields on this board because you may pull the WiFi antenna.

The text of the Arduino getting started guide is licensed under a Creative Commons Attribution-ShareAlike 3.0 License. Code samples in the guide are released into the public domain.

Источник

UNO WiFi Rev2

The Arduino UNO WiFi Rev2 is the easiest point of entry to basic IoT with the standard form factor of the UNO family. Whether you are looking at building a sensor network connected to your office or home router, or if you want to create a Bluetooth® Low Energy device sending data to a cellphone, the Arduino UNO WiFi Rev2 is your one-stop-solution for many of the basic IoT application scenarios.

The Arduino UNO WiFi Rev 2 features the secure ATECC608 crypto chip accelerator, using the ATmega4809 8-bit microcontroller from Microchip. It also has an onboard IMU (Inertial Measurement Unit), LSM6DS3TR and features the NINA-W102 Wi-Fi & Bluetooth® module from u-Blox.

Enables Bluetooth® and Wi-Fi connectivity for the UNO WiFi Rev2 board.

The UNO WiFi Rev2 comes with the LSM6DS3TR, a low-power IMU module that includes a 3D digital accelerometer & gyroscope.

Here you will find the technical specifications for the Arduino UNO WiFi Rev 2.

Board	Name	Arduino® UNO WiFi Rev 2
	SKU	ABX00021
Microcontroller	ATmega4809
USB connector	USB-B
Pins	Built-in LED Pin	25
	Digital I/O Pins	14
	Analog input pins	6
	PWM pins	5
Connectivity	Bluetooth®	Nina W102 uBlox module
	Wi-Fi	Nina W102 uBlox module
	Secure element	ATECC608A
Sensors	IMU	LSM6DS3TR
Communication	UART	Yes
	I2C	Yes
	SPI	Yes
Power	I/O Voltage	5V
	Input voltage (nominal)	6-20V
	DC Current per I/O Pin	20 mA
	Power Supply Connector	Barrel Plug
Clock speed	Processor	ATmega4809 16 MHz
Memory	ATmega4809	6KB SRAM, 48KB flash, 256 bytes EEPROM
	Nina W102 uBlox module	448 KB ROM, 520KB SRAM, 2MB Flash
Dimensions	Weight	25 g
	Width	53.4 mm
	Length	68.6 mm

Software & Cloud

The following software tools allow you to program your board both online and offline.

Hardware

The hardware listed below is compatible with this product.

Источник