Debian network configuration wifi

Как настроить WiFi

Если ваше устройство имеет беспроводной интерфейс (контролируемый утилитой iwconfig), он должен быть настроен для подключения к сети. Если у вас отсутствует интерфейс для устройства, пожалуйста, посетите WiFi для получения информации об установке драйвера.

Беспроводной интерфейс может быть настроен с помощью менеджера соединения (например, NetworkManager) или через /etc/network/interfaces с помощью специальных утилит (например, wpa_supplicant). Настройки NetworkManager и wpa_supplicant приведены ниже.

<! data-lazy-src=

<i data-lazy-src=

How to Set Up WiFi in Debian With The Command Line

debian wifi setup

In this article, we’ll guide you on how to connect to WiFi from the command line on the Debian 11/10 server and desktop using the wpa_supplicant. The wpa_supplicant is an implementation of the WPA protocol’s supplicant component.

To set up Wi-Fi in Debian with the command line, you need to establish a Wi-Fi network connection before ensuring that it’s connected automatically at boot time. Keep reading to find a step-by-step guide on how to do so.

Debian Wi-Fi

Wireless devices using Wi-Fi operate on chipsets found in several different devices. Debian is a free, software-based system that depends on the manufacturers’ and developers’ cooperation in producing quality drivers/modules for those chipsets.

How to Set Up WiFi in Debian With The Command Line

There are two phases to complete for the setup of WiFi in Debian with the command line.

Here’s a complete step-by-step procedure for each phase of the setup.

How to Establish a WiFi Connection

To establish a WiFi network connection in Debian, you need to follow these steps:

  • Enable The Network Card
  • Detect WiFi Networks
  • Configure The WiFi Connection With The Access Point
  • Obtain a Dynamic IP Address With DHCP Server
  • Add a Default Route to The Route Table
  • Verify The Internet Connection

Here’s how you perform each step.

Enable The Network Card

Follow these steps to enable the network card.

  • To enable the WiFi card, you must first identify the wireless card with the following command: iw dev.
  • Then, you can note the name of the wireless device. The string might be lengthy, so you can use this variable to eliminate the typing effort: export wlan0=.
  • Bring up the WiFi card with the above command: sudo ip link set $wlan0 up.

Detect WiFi Networks

Follow these steps to detect the WiFi networks.

  • To detect WiFi networks in Debian, look for available networks in the wireless network interface with the following command: sudo iw $wlan0 scan.
  • Ensure that your access points SSID is one of the available networks detected.
  • This variable eliminates the typing effort: export ssid=.

Configure The WiFi Connection With The Access Point

Follow these steps to configure the network connection with the access point.

  • Use the wpa_supplicant service to establish an encrypted network connection to the access point. It will only use the configuration file “/etc/wpa_supplicant.conf,” containing the wpa2-keys for every SSID.
  • To connect to the access point, add an entry for the config file: sudo wpa_passphrase $ssid -i >> /etc/wpa_supplicant.conf.
  • Use this command to connect to the access point: sudo wpa_supplicant -B -D wext -i $wlan0 -c /etc/wpa_supplicant.conf.
  • Confirm your connection to the access point with this: iw $wlan0 link.

Obtain a Dynamic IP Address With DHCP Server

Follow these steps to obtain a dynamic IP with DHCP.

  • Obtain a dynamic IP with DHCP using this: sudo dhclient $wlan0.
  • View the IP with this command: sudo ip addr show $wlan0.

Add a Default Route to The Route Table

Follow these steps to add a default route to the route table.

  • Inspect the route table with this: ip route show.
  • Add a default route to the router to connect to WiFI with this command: sudo ip route add default via dev $wlan0.

Verify The Internet Connection

Finally, use the following command to verify that you’ve connected to the network: ping www.google.com.

How to Auto Connect at Boot Time

To ensure that the wireless network auto-connects at boot-up, you need to create and enable a systemd service for:

Here’s how you perform each step.

Dhclient Service

  • Create this file: /etc/systemd/system/dhclient.service.
  • Then, edit the file by performing this command:

Wpa_supplicant Service

  • Go to “/lib/systemd/system,” copy the service unit file, and paste it to “/etc/systemd/system” using the following lines: sudo cp /lib/systemd/system/wpa_supplicant.service /etc/systemd/system/wpa_supplicant.service.
  • Use an editor, such as Vim, to open the file on “/etc” and modify the ExecStart line with this: ExecStart=/sbin/wpa_supplicant -u -s -c /etc/wpa_supplicant.conf -i .
  • Then, add this line below: Restart=always.
  • Comment this line: Alias=dbus-fi.w1.wpa_supplicant1.service.
  • Reload the service with this line: sudo systemctl daemon-reload.
  • Enable the service with this line: sudo systemctl enable wpa_supplicant.

How to Create a Static IP

Follow these steps to obtain a static IP address:

  • First, disable dhclient.service to obtain a static IP address.
  • Then, create a network configuration file: sudo nano /etc/systemd/network/static.network.
  • Add these lines:
  • Please save the file before closing it. Then, create a .link for the wireless interface with this: sudo nano /etc/systemd/network/10-wifi.link.
  • Add these lines in the file:
  • In this case, you need to use your MAC address and wireless interface name. By doing that, you’ll ensure that the system doesn’t change the wireless interface name.
  • Please save the file before closing it. Then, disable “networking.service” and enable “systemd-networkd.service.” This is the network manager. Use this command to do so:

sudo systemctl disable networking

sudo systemctl enable systemd-networkd

  • Restart the systemd-networkd to check the working of the configuration with this: sudo systemctl restart systemd-networkd.

Conclusion

After reading the guide, you can easily create a network connection in Debian using the command line.

Hedayat S

Hedayat is the new Editor-in-Chief of Rottenwifi and has been writing about computer networking since 2012. Hedayat’s strong background in computer science helped him cement his position in the ever-expanding tech blogging world. As a network engineer, systems administrator, and systems analyst during his decade-long career in Information Technology, he has a passion for the internet & technology in his DNA.

Blog.rottenwifi.com is a participant in the Amazon Services LLC Associates Program which means we may get paid commissions on editorially chosen products purchased through our links to retailer sites. All names, logos, brands, and images are trademarks or copyrighted materials of their respective owners. Amazon and the Amazon logo are trademarks of Amazon.com, Inc., or its affiliates.

Источник

Читайте также:  Автоматический поиск сети wifi
Оцените статью
Adblock
detector