Default password unifi wifi

Ubiquiti UniFi AP Pro Default Router Login

To get access to your Ubiquiti UniFi AP Pro ( also known as UniFi AP ), you need the IP of your device, the username and password. You’ll find such information in the Manual of your Ubiquiti UniFi AP Pro router. But if you do not have the manual for your router or you do not want to read the whole manual to find the default login information then you can use the quick guide below. To get to the router login page it’s necessary that you are connected to the router.

Ubiquiti UniFi AP Pro Login Guide

• Open your web browser (e.g. Chrome, Firefox, Opera or any other browser)
• Click HERE to auto detect your router IP. After some seconds our tool will show a link to your router login page. Click on the shown link.
• You should see 2 text fields where you can enter a username and a password.
• The default username for your Ubiquiti UniFi AP Pro is ubnt.
  The default password is ubnt.
• Enter the username & password, hit «Enter» and now you should see the control panel of your router.

If above login credentials doesn’t work with your Ubiquiti UniFi AP Pro router then try this method

Try different ID/password combinations that are widely used by Ubiquiti that you’ll find below. In this list are the most popular default username and password combinations used by Ubiquiti. Sometimes the username and password doesn’t work that we mentioned in the top of this guide. Then you can try these username/password combinations below to get access to your Ubiquiti UniFi AP Pro wireless router.

#	Username	Password
1	ubnt	ubnt
2	(blank)	(blank)
3	admin	admin

Default login IPs for my Ubiquiti router

You tried different router IPs but nothing worked? Did you try the following IPs? In the list below we listed all known router IPs for the manufacturer Ubiquiti. Maybe this will work for you.

#	Default Router IP
1	192.168.1.1
2	192.168.1.20
3	192.168.124.1
4	192.168.25.115
5	acquired via DHCP
6	192.168.2.1
7	192.168.0.1
8	192.168.1.254

Nothing of the methods worked for me and I still not get access to my Ubiquiti UniFi AP Pro!

All you need to do is to reset your UniFi AP Pro modem. This can be done easily by clicking on the reset button at the back or at the bottom of your router. If you hold down this small button for approximately 20 seconds, (you may have to use a toothpick), then your modem will get restored to the factory settings. What you need to keep in mind is that when you reset your modem, you will lose your connection online. It is therefore better to take an expert’s assistance in this regard. Note: If you have not enough information, it is obviously recommended that you should get help from a person who has all the knowledge about this topic.

Источник

Ubiquiti Unifi Default Username Password

Scenario
Make: Ubiquiti
Model: Ubiquiti Controller or Unifi Access Point [UAP-nanoHD]
Description: In this article, we will discuss the Unifi default password which is the default for Ubiquiti Unifi Controller, Ubiquiti Unifi access points. It can be used for setting up the Ubiquiti controller and Unifi access point with default Username & Password

Controller Setup

If you have new Ubiquiti wireless access points and you are looking to set them up, you would need to set up the Ubiquiti controller first. The controller can be set up locally or at a remote site. It could be on a local laptop or desktop or maybe somewhere in the data centre so that all access points would be managed at one location under one controller interface.

Once the controller is fully set up below is the screenshot of the controller login page.

Password setup

During setting up the controller you would need to install the Ubiquiti Controller software and after the successful installation of the software, you would need to set up the password.

Note: once the software is installed it will ask to set up a new password.

Set username and password and it is highly recommended to keep the username and password somewhere safely either on online secure password manager or at any safe place which can be accessed easily as you would need to login to the page many times and you will be thankful to yourself that you have saved the password earlier.

Username & Password

Another scenario is when we need to log in to unify access points via SSH. So when we try to SSH access point we need a username and password. Here we could have two situations

When the unifi access point, security gateway or switches have not been adopted yet by the controller and we want to SSH the access point. So before the adoption of the access point, unifi security gateway, Unifi switches or any Ubiquiti Unifi network devices, the default username and password for the Unifi network devices would be

username = ubnt
password = ubnt

If the access point is already adopted by the controller and we want to SSH the access point then at the time of adoption controller generates a password for save it in the controller. Please refer SSH Ubiquiti access point to know the steps of how to ssh access point after adopted by the controller.

If you are unable to get the password or the default password is not working you might need to Factory Reset Ubiquiti Unifi Access Point . Please refer to the article how to reset the access point to factory default.

Источник

Ubiquiti Default Password

We have gathered all working passwords for Ubiquiti Default Password for your comfort in the post.

Login Procedure

1. Enter the IP address 192.168.1.20 into your browser and hit Enter.
2. If no login screen appears, try looking up your router’s IP address by searching for it.
3. Enter the username for your router.
4. If you changed the username on the router and can’t remember it, try resetting your router. This may be ubnt or one of these.
5. Type in the router password.
6. This might be one of these or ubnt.
7. Enter the key or select the login button.
8. If you encounter a login error, try retrieving your router’s default login credentials and attempting again.

Software Installation

Insert the UniFi Controller software CD into your CD-ROM drive and follow the instructions for your specific computer type.

1. Click the Install icon.
2. Click Continue and follow the on-screen instructions to install the software.
3. Go to Go > Applications and double-click the UniFi icon.

Insert the UniFi Controller software CD into your CD-ROM drive and follow the instructions for your specific computer type.

1. Launch UniFi-installer.exe.
2. Click Install.
3. If your computer doesn’t have Java 1.6 or above installed, you will be prompted to install it. Click Install to continue.
4. Click Next.
5. Ensure that the Start UniFi Controller after installation option is checked and click Finish.

Источник

What is the Default Username & Password for UniFi Access Points?

So, you’ve just got your shiny new UniFi Access Point and have yet to go through the setup process of installing the unit. During this process when you adopt the UniFi wireless AP into the controller software you will be asked to assign a username and password – to be clear, this isn’t asking you what the current username and password is, it’s asking you to assign new ones (that you have thought of with your own fragile mind).

This is what the UniFi Controller Software login screen will look like:

So, in the above specific situation, where a customer is setting up a UniFi Access Point for the first time and using the Ubiquiti Controller Software to manage the AP, you will need to create a memorable username and password of your own and write it down; make sure you keep this somewhere safe, store a physical copy somewhere (where you won’t lose it or forget where you put it) and create a text file on your phone or laptop with this information stored for future use. Inevitably at some point you will need to use this username and password again – and you will thank yourself when you remember where it is you stored that information!

Another scenario involving the default username and password for UniFI Access Points (and many other Ubiquiti products) would be when accessing the unit via SSH – in this case (and if you haven’t already adopted the AP into the controller software as mentioned above), you would then need to use the default username and password – this has always been Username: ubnt and Password: ubnt. As long as the UniFi Access Point has not been previously setup or adopted by the software, and only if you are attempting to connect via SSH, then always use the default username and password of ubnt / ubnt.

When customers initially setup their UniFI Access Point in the controller software, if you don’t specify a password when you add a new location or access point, it will auto generate a password for you. This information can be found by looking in the very bottom left corner of the UniFi Software Dashboard and clicking on the small gear icon – this will bring you to the settings page where the username and password are available to view or edit – this is in the bottom section of the screen, labelled “Device Authentication“, simple click the tiny eye icon to reveal your password. Your settings page should look something like the below (depending on the version of the software you’re using):

*Note the screenshot below is a newer version of the software, some customers may not see reference to SSH, it will simply read “Device Authentication” – this is where the auto-generated password will be shown. Each new device or location will have a settings page like this – you can access each individual settings page for different APs by clicking the dropdown box the top right of the dashboard, labelled “Locations“.

Another possible situation you might also encounter with regards to the default username and password of the UniFi Access Point, is if the AP has had SSH already enabled within the UniFi Controller Software. You can double check if this is the case by logging into the UniFi Controller Software, then click the tiny gear icon in the bottom left corner to go to the settings page – on this page, at the bottom, you will see something similar to the above screenshot, where if SSH has been enabled, the blue check box next to “Enable SSH Authentication” will be ticked and you will see the username and password displayed. You will need to click the tiny eye icon on the right of the password field in order to view the current password. Alternatively, if this has not been set up, these details will be left blank and you can choose to enable this depending on your requirements – in this case, you can either assign your own credentials or the software will create them for you (just make sure you note them down).

Finally, as a last resort and if all else fails (this really shouldn’t be necessary if the above methods have been used), you can always factory reset a UniFi access point as detailed in our blog post. After this process you can then reassign a new username and password via the above methods.

Источник