Fosi audio t20 aptx hd bluetooth

Preparation

Prepare 2: Insert the tube carefully and ensure that all pins are fully inserted.

Prepare 3: • Connect the T20 to the passive speakers via the speaker wires; you can connect the speaker’s wire via the bare wire or the banana plugs;

• Or Connect a wired headset to the Headphone Output on the front panel of the T20, the speaker output will disconnect once the headset is plugged in.

Prepare 4: Connect the 24V power supply to the DC input;

Prepare 5: Turn on the Power Switch.

Note: Before turning on the amplifier’s power switch, please turn the volume button to the lowest position.

Note: Be sure that the power switch is OFF before connecting the power supply. Please turn on the T20 first and turn on the speakers to avoid noise.

How to connect the speaker wire?

Method 1: Bare wire connection illustration

①: Release the horn terminals block terminals;

②: Insert the two ends of the speaker wire into the amplifier and speaker terminal holes;

③: Tighten the horn terminals;

Method 2: Banana plugs connection illustration

1 : Release the banana jacket;

3 : Insertion speaker wire and tighten the screw;

4 : Tighten the banana jacket;

5 : Insert the banana plug into the horn terminals of the speaker and amplifier.

Please make sure that the speakers’ wires are not attached; the speaker connection area is very narrow, and it is easy to cause the positive and negative speakers’ wires to contact each other, which will result in no sound output.

Bluetooth Input

Prepare your Bluetooth device (take a phone as an example).

Step 1: Install the Bluetooth antenna.

Step 2: Select the input mode switch to BT on the back panel of the T20; the indicator is blue and blinking.

Step 3: Turn on the Bluetooth on your phone and search “ Fosi Audio” or “Fosi Audio T20.” The indicator stays blue after a successful pairing.

Step 4: Open the audio application, play it, and enjoy!

AUX Input

Prepare an audio source (take a TV, for example), an RCA cable, or a 3.5mm AUX to RCA cable.

Step 1: Select the input mode switch to AUX on the back panel of the T20; the indicator light shows red;

Step 2: Connect your TV to “Audio Input” via an RCA cable;

Step 3: Open your TV, play, and enjoy!

Troubleshooting

1: What type of speakers work best with T20 Amplifiers?

• Fosi Audio Amplifiers work great with any 2-8 ohm passives peakers. You can connect passive speakers via the Speaker Output or active speakers via the Headphone Output.

2: Can I connect a turntable to T20 amp? Why is the volume deficient?

• As the turntables do not have a built-in preamp, you need to add an external phono preamp before connecting T20, such as our BOX X1 or BOX X2.

• As for the turntables with a built-in preamp, you need to switch the preamp on before connecting T20.

3: Why does the sound crack or make a lot of electric noise?

• Please make sure all the cables are completely pushed into the devices, incompletely connection will cause this cracking.

• Please remove all the inputs and check whether the cracking noise disappears; the cracking may be from the audio source or input cables.

• If you are not using the original factory standard power supply, please replace the power supply before testing. Many power supply in the market has a large interference coefficient, which will cause a lot of current sounds.

• Please check if the vacuum tube is completely plugged in, and try to change the left and right vacuum tubes.

4: My Bluetooth device cannot pair with T20?

• Make sure that you have selected the input mode switch to BT on the back panel of the T20.

• Make sure that T20 is powered on.

• Make sure that T20 is not paired with other devices.

• Make sure that the distance between your device and T20 is not too long.

• Make sure there are no barriers between your device and T20; barriers will affect the Bluetooth operation distance.

• Please reconnect the power supply to the T20, and move the T20 to another room to have a try.

• Restart the T20 and then try to connect again; try to use another Bluetooth device.

5: Why is Bluetooth intermittent?

• Please try with another Bluetooth device.

• Make sure there is no interference between the T20 and the audio source from other electronic devices.

• Place your device close to the T20, and plug in the power adapter again.

6: How much power does it take in standby mode? Can this amp be left on all the time?

• This is the class D amplifier; it will cost meager power in standby mode. It can be connected all the time, and it is safe without power consumption.

7: Sound quality is not good?

• Make sure all the cables are fully connected.

• Adjust the treble and bass control of the power amplifier to achieve the right tone.

• Please try to change the sound source and cables to test.

• Please check if the vacuum tube is broken or completely plugged in.

8: Can T20 accept a signal from a Bluetooth microphone?

• Please make sure your Bluetooth microphone must be the transmitter. Because T20 is a Bluetooth receiver amplifier.

• Please make sure that the microphone’s Bluetooth can be connected to the T20’s Bluetooth by your operation.

9: Why does the sound cut in and out?

• Please try to change the sound source.

• Lower the treble and bass of the T20.

• Make sure that the positive and negative terminals of the speaker outputs do not touch each other. Some of the larger banana plugs can easily touch each other and cause a short circuit

10: Can I bridge channel 1 and channel 2 to get 100watts?

• No, this amplifier can’t be bridged.

11: Why does distortion occur?

• Because the vacuum tubes amplify the sound. If you turn the sound up too loud, distortion may occur. Please try turning the volume down a little.

12: Can I replace the vacuum tubes?

• If necessary, there are substitutions: EF95, 6AK5, 6AK5W, 403A/403B, 6J1, 6J1P, 6J2, 6J3, 6J4, 6J5 vacuum tubes, etc. You can replace the vacuum tubes to DIY your stereo system.

Note: Please must remember to switch off the power BEFORE you pull out the tube, or it might damage the device.

13: Why does the T20 come with a broken vacuum tube?

• Due to the long distance, the vacuum tube may be damaged during transportation. If you find that the vacuum tube is broken or there are other problems, please contact our email, and we will replace the vacuum tube for you.

14: Can headphones and speakers play at the same time?

• No, the speakers’ output will be interrupted when the headphones plugin.

Output priority:

3.5mm Headphone Output > Speaker Output

15: How can I connect T20 to TV?

• The 3.5mm AUX jack is the audio input. It can go through 3.5mm AUX input to connect your TV.

16: Why is there no voice from my amplifier?

• Please check whether the power supply cable is connected to T20 and whether the power indicator is on.

• Make sure the T20’s indicator light is on when the power is turned on.

• Please check that the T20 and your source components are turned on and not set to minimum volume; if possible, replace your source and test again.

• Check that the wire connections from the audio source to each speaker in the amplifier are connected correctly.

• Please check that the cable is not loose or damaged. Incomplete connection is one of the main reasons for no sound.

• Please ensure the Bluetooth is paired or not; if Bluetooth is connected, AUX input will be disconnected. If you want to connect this amplifier with a 3.5mm AUX cable, you need to disconnect the Bluetooth first.

• Please make sure that the headset is connected or not. If the headset is connected, the speaker will be disconnected.

17: Which Bluetooth chip does T20 have?

• The T20 is equipped with QCC3031 Bluetooth chip, which supports Apple acc and aptx.

Note: The QCC3031 Bluetooth chip does not support apt-X LL.

18: Can I use Bluetooth headphones with this unit?

• This tube amplifier is a Bluetooth receiver, not a Bluetooth transmitter. It works with 3.5mm wired headphones.

Источник

Ламповый усилитель Fosi Audio T20 AptX-HD Bluetooth с блоком питания, арт. 1430

Fosi Audio T20 — компактное устройство, которое сочетает в себе возможности усилителя для пассивной акустики и лампового предусилителя с двумя лампами 6J4 отличается возможностью беспроводного подключения по Bluetooth 5.0 с кодеком AptX-HD, регулировки усиления, тембра верхних частот и баса, а также низким уровнем шума и искажений. Устройство может использоваться с пассивной акустикой от 2 до 8 ом или наушниками от 16 до 64 Ом. Для подключения источника используются стандартные разъемы RCA. Предварительный усилитель не занимает много места и улучшает характеристики звука. Fosi Audio T20 работает от блока питания, который входит в комплект.

Корпус усилителя полностью выполнен из металла, на верхней части находятся вырезы для установки ламп. Вход и выход RCA позолочены для более стабильного соединения и расположены сзади, что позволяет удобно спрятать провода. Джек 3.5 для подключения наушников или активной акустики находится на передней панели.

Fosi Audio T20 работает от блока питания, который входит в комплект. Размер предварительного усилителя составляет всего 129,5x99x33 мм, он отлично смотрится на столе или тумбе. Производитель расположил на корпусе светодиоды, которые включаются во время использования и подсвечивают лампы приятным синим цветом.

На лицевой части предусилителя располагается три ручки, которые отвечают за регулировку тембра верхних и низких частот, а также общей громкости. При необходимости лампы можно заменить на совместимые: 6K4, 6J1, GE5654, 6AK5, 6ж1П, 6BC5, 403A/B, EF40, EF95 и подобные.

Комплектация: 1 x Fosi Audio T20 1 x блок питания 12В/1А.

Характеристики:
Модель: T20
Адаптер питания: 24 В/4,5a
Диапазон входного сигнала постоянного тока: 12-24 В
Сопротивлени наушников: 16-64 Ом
Сопротивление динамиков: 2 Ом-8 Ом
Максимальная выходная мощность: 50 Вт x 2
THD ≤ 0.04%, SNR ≥ 99дб
Чип усилителя: TPA3116
Входная чувствительность ≤ 280мв
Частотный диапазон: 20 Гц-20 КГц
Подключение: Bluetooth и RCA
Расстояние передачи Bluetooth: до 12 м
Bluetooth: QCC3031, Bluetooth 5,0, поддержка apt-X HD

Источник

Fosi Audio T20 AptX-HD Bluetooth с блоком питания

Перед приобретением Fosi Audio T20 AptX-HD Bluetooth с блоком питания по самой низкой цене, изучите характеристики, плюсы и минусы модели, отзывы покупателей.

Характеристики Fosi Audio T20 AptX-HD Bluetooth с блоком питания

Основные характеристики *

Цвет товара	черная
Тип	усилитель мощности
Количество каналов	2
Схемотехника	ламповый

Параметры усилителя *

Мощность	50 Вт/канал
Чувствительность (лин. вход)	280 мВ
Минимальная воспроизводимая частота	20 Гц
Максимальная воспроизводимая частота	20000 Гц
Коэффициент гармоник	0.04 %
Отношение сигнал/шум	99 дБ

Подключение *

Беспроводная связь	Bluetooth
Разъемы и интерфейсы	RCA
Разъемы на передней панели	выход на наушники
Стандарт Bluetooth	5.0

Прочее *

Комплектация	1 x Fosi Audio T20, 1 x блок питания 12В/1А
Ширина	9.9 мм
Высота	3.3 мм
Глубина	12.9 мм

* Точные параметры уточняйте на сайте продавца.

Приобретением пока доволен: оправдал мои ожидания, дальше время покажет.

Достоинства: Новизна в прослушивании любимой музыки: давно хотелось послушать этот «ламповый звук», о котором много слышал хороших отзывов. Пока только положительные эмоции от приобретения!

Недостатки: не нашёл таких

Источник