Initramfs linux fallback img
Установил blackarch, ИСОшник на 4,4Гб взял здесь — https://blackarch.org/, после установки ОС обновилась без проблем, и всё бы казалось хорошо, однако обнаружил отсутствие в boot — initramfs-linux-fallback.img, система устанавливалась на один раздел с ext4 в режиме bios .
Как я понимаю генерирует initramfs-linux.img, initramfs-linux-fallback.img — mkinitcpio.
Имеется так же установленный чистый арч, в котором initramfs-linux-fallback.img сгнерировался при установке ОС, при сравнении mkinitcpio.conf особых различий не увидел-
blackarch:
# # SPDX-License-Identifier: GPL-3.0-or-later # vim:set ft=sh # MODULES # The following modules are loaded before any boot hooks are # run. Advanced users may wish to specify all system modules # in this array. For instance: # MODULES=(piix ide_disk reiserfs) MODULES="" # BINARIES # This setting includes any additional binaries a given user may # wish into the CPIO image. This is run last, so it may be used to # override the actual binaries included by a given hook # BINARIES are dependency parsed, so you may safely ignore libraries BINARIES=() # FILES # This setting is similar to BINARIES above, however, files are added # as-is and are not parsed in any way. This is useful for config files. FILES="" # HOOKS # This is the most important setting in this file. The HOOKS control the # modules and scripts added to the image, and what happens at boot time. # Order is important, and it is recommended that you do not change the # order in which HOOKS are added. Run 'mkinitcpio -H ' for # help on a given hook. # 'base' is _required_ unless you know precisely what you are doing. # 'udev' is _required_ in order to automatically load modules # 'filesystems' is _required_ unless you specify your fs modules in MODULES # Examples: ## This setup specifies all modules in the MODULES setting above. ## No raid, lvm2, or encrypted root is needed. # HOOKS=(base) # ## This setup will autodetect all modules for your system and should ## work as a sane default # HOOKS=(base udev autodetect block filesystems) # ## This setup will generate a 'full' image which supports most systems. ## No autodetection is done. # HOOKS=(base udev block filesystems) # ## This setup assembles a pata mdadm array with an encrypted root FS. ## Note: See 'mkinitcpio -H mdadm' for more information on raid devices. # HOOKS=(base udev block mdadm encrypt filesystems) # ## This setup loads an lvm2 volume group on a usb device. # HOOKS=(base udev block lvm2 filesystems) # ## NOTE: If you have /usr on a separate partition, you MUST include the # usr, fsck and shutdown hooks. HOOKS="base udev autodetect modconf block keyboard keymap filesystems fsck" # COMPRESSION # Use this to compress the initramfs image. By default, gzip compression # is used. Use 'cat' to create an uncompressed image. #COMPRESSION="gzip" #COMPRESSION="bzip2" #COMPRESSION="lzma" #COMPRESSION="xz" #COMPRESSION="lzop" COMPRESSION="lz4" #COMPRESSION="zstd" # COMPRESSION_OPTIONS # Additional options for the compressor #COMPRESSION_OPTIONS=() # vim:set ft=sh # MODULES # The following modules are loaded before any boot hooks are # run. Advanced users may wish to specify all system modules # in this array. For instance: # MODULES=(usbhid xhci_hcd) MODULES=() # BINARIES # This setting includes any additional binaries a given user may # wish into the CPIO image. This is run last, so it may be used to # override the actual binaries included by a given hook # BINARIES are dependency parsed, so you may safely ignore libraries BINARIES=() # FILES # This setting is similar to BINARIES above, however, files are added # as-is and are not parsed in any way. This is useful for config files. FILES=() # HOOKS # This is the most important setting in this file. The HOOKS control the # modules and scripts added to the image, and what happens at boot time. # Order is important, and it is recommended that you do not change the # order in which HOOKS are added. Run 'mkinitcpio -H ' for # help on a given hook. # 'base' is _required_ unless you know precisely what you are doing. # 'udev' is _required_ in order to automatically load modules # 'filesystems' is _required_ unless you specify your fs modules in MODULES # Examples: ## This setup specifies all modules in the MODULES setting above. ## No RAID, lvm2, or encrypted root is needed. # HOOKS=(base) # ## This setup will autodetect all modules for your system and should ## work as a sane default # HOOKS=(base udev autodetect modconf block filesystems fsck) # ## This setup will generate a 'full' image which supports most systems. ## No autodetection is done. # HOOKS=(base udev modconf block filesystems fsck) # ## This setup assembles a mdadm array with an encrypted root file system. ## Note: See 'mkinitcpio -H mdadm_udev' for more information on RAID devices. # HOOKS=(base udev modconf keyboard keymap consolefont block mdadm_udev encrypt filesystems fsck) # ## This setup loads an lvm2 volume group. # HOOKS=(base udev modconf block lvm2 filesystems fsck) # ## NOTE: If you have /usr on a separate partition, you MUST include the # usr and fsck hooks. HOOKS=(base udev autodetect modconf kms keyboard keymap consolefont block filesystems fsck) # COMPRESSION # Use this to compress the initramfs image. By default, zstd compression # is used. Use 'cat' to create an uncompressed image. #COMPRESSION="zstd" #COMPRESSION="gzip" #COMPRESSION="bzip2" #COMPRESSION="lzma" #COMPRESSION="xz" #COMPRESSION="lzop" #COMPRESSION="lz4" # COMPRESSION_OPTIONS # Additional options for the compressor #COMPRESSION_OPTIONS=() # MODULES_DECOMPRESS # Decompress kernel modules during initramfs creation. # Enable to speedup boot process, disable to save RAM # during early userspace. Switch (yes/no). #MODULES_DECOMPRESS="yes" Познания мои не шибко обширые в таких вопросах, прошу уважаемых гуру растолковать в чём может быть проблема.
К тому же ядра в обеих системах одинаковые, тупо скопировал initramfs-linux-fallback.img из archlinux в blackarch, сгенерировал grub.cfg и нормально загрузился с initramfs-linux-fallback.img .