Линукс минт настройка сети

How to configure a network on Linux Mint

It is always suggested that you execute some essential network setups while working on your operating system before utilizing the internet on any device. These settings are made to guarantee that your internet is running smoothly and with all of the protocols that you want it to. Also, if your Internet is slow or you’re having difficulties connecting to it, you should always check the network parameters to see if anything is wrong.

Similarly, as a network administrator, your major responsibility is to monitor several activities throughout a network, and network configuration allows them to trace any changes that influence the network’s performance. Administrators can decrease network downtime by using change tracking software. If a system upgrade degrades network performance, you can revert to a previous configuration that worked well.

Linux Mint is well-known for its power, reliability, and security. Network configuration is a comprehensive process that involves setting up network controls, managing network traffic, and operating the network to facilitate network communication. So this article will cover some of the basic details that are necessary to configure your network.

How to find your IP address on Linux Mint

Before the network configuration, it is better to know your own IP address first so that you can reset it later if needed by typing.

After typing this command, you will find your IP address on the second point which is the ens33 network configuration port that can be seen in the image.

You can also check your IP address from the network settings as well, and for that, you need to click on the menu and select Network settings.

How to do network configuration on Linux Mint using Network settings

Your system will be assigned by the default IP address that is currently available from the network pool. You can configure your network by going into the network settings that you can find on the menu bar, as shown below. After that, you need to click on the bottom right “gear icon” option to open network settings for you.

Next, you need to click on the IPv4 tab, and there you will see that your network is set to “Dynamic Host Control Protocol (DHCP)” by default, and some other options can also be seen there.

DHCP is used to provide you with the IP address automatically, but if you want to configure the network settings manually, you need to set it to the “Manual” from the drop-down menu.

Now you can configure your network manually and need to provide the values for the network address. For example, the values that we have selected in our case are mentioned below.

Address: 192.168.114.100

Netmask: 255.255.255.0

Gateway: 192.168.114.2

After providing the required values, you need to click on the “Apply” button, and then new settings will be implemented.

Now verify the new settings, and for that, you need to open your network settings again, and there you will see this new information:

How to configure your network using the NMTUI utility

You can check your current network IP address either by the terminal or from the network settings. So to check it from the terminal, you can type:

To configure your network using the NMTUI utility, you need to use the command given below:

This will open a new window in the terminal with multiple options, as shown below. You need to select the “Edit a connection” option to configure the network.

After selecting this option, you need to choose your network connection and click on the “Edit” tab.

Choose the IPv4 tab and then “Manual” settings:

This will open all the necessary settings for you that are required to configure a network. Here we have implemented the same network settings as mentioned in the previous part as displayed below.

After applying settings, the next step is to go back to the main menu and select option, “Activate connection“:

To activate the newly applied settings, you need to deactivate your network connection and then again activate it.

This will refresh your network settings so that new settings can be applied, and later you can also verify this by typing again the previously discussed command in the terminal.

How to reset network settings

To reset all the network settings, use :

The “INPUT” and “OUTPUT” are the chains consist of rules for incoming and outgoing connections, where the “F” option is for flush:

$ sudo iptables -P INPUT ACCEPT

$ sudo iptables -P OUTPUT ACCEPT

And “P” option to set the policy to target chain:

Then execute the command mentioned below:

And now reboot your system using:

How to configure incoming and outgoing traffic

If you want to configure your network to allow or block your network to communicate with an outside world then you can do that by configuring a firewall. One way of doing this is by installing an uncomplicated firewall (UFW) and you can do that by typing.

After its installation, you need to make sure that your firewall is enabled and currently active by typing

Now if you want to allow or deny any specific port for communication then you can do that by typing

And later you can verify if these rules have been implemented or not by typing again.

In the same way, you can also disable any network port by typing.

Conclusion

Once you’ve set up your network connection according to your preferences, you won’t have any problems utilizing the Internet on your Linux Mint. Furthermore, if you ever feel that any of your configurations have become screwed up, you can always go back to your network settings and correct the problem in the same way we outlined in this article. By following this approach, you will not only improve your networking knowledge but will also be able to resolve the majority of your network-related problems on your own.

About the author

Taimoor Mohsin

Hi there! I’m an avid writer who loves to help others in finding solutions by writing high-quality content about technology and gaming. In my spare time, I enjoy reading books and watching movies.

Источник

Как в Linux Mint 20.1 настроить сеть

Наверное одно из первых действий которые делает любой пользователь после установки операционной системы это настраивает подключение к локальной сети (Интернету). В большинстве случаев достаточно подключить сетевой кабель к компьютеру. Так как практически в каждой квартире есть роутер который раздает в автоматическом режиме всем подключенным к нему устройствам настройки сети, с помощью настроенного в нем DHCP сервера. Подобные схемы реализованы практически везде. Но бывают ситуации когда нужно вручную указать сетевые настройки, например, для того чтобы соединить два компьютера напрямую кабелем. В этом случае необходимо уметь настаивать все это дело в ручную. Сегодня расскажу как можно изменить настройки подключения к сети в Linux Mint.

Если вы используете Linux Mint или планируете перейти на неё то следующие статьи будут вам очень полезны.

Как изменить параметры подключения к сети

Открыть настройки сети можно из «Центра управления» выбрав раздел «Интернет и сеть» и пункт «Расширенная конфигурация сети», либо кликнув ПКМ на значке подключения к сети и выбрав пункт «Изменить соединения» который расположен на панели задач.

В открывшемся окне будут отображены все подключения, в большинстве случаев оно всегда одно. Все завесит от количества установленных сетевых карт и настроенных подключений. Выделяем его и снизу на панели жмем на настройки.

Первое что рекомендую сделать это изменит имя подключения на что то более понятное. Обычно если это подключение к интернету то его называют WAN, а подключение к локальной сети LAN. Это на будущие, вдруг у вас будет 10 подключений). Из всех вкладок вам понадобиться только «Параметры IPv4». Если вы подключаете компьютер к сети в которой есть DHCP сервер то поле метод нужно выбрать пункт «Автоматическое DHCP». А если вы хотите указать все настройки вручную то выбираем «Вручную» и ниже вводим IP адрес, Маску сети, шлюз и сервер DNS.

На этом самая простая настройка сети в операционной системе Linux Mint 20.1 MATE завершена. В принципе для того чтобы иметь простой доступ в интернет этого достаточно. О том как настроить VPN, прокси и прочие расскажу в следующей статье.

Источник