Linux configure kernel modules

Linux configure kernel modules

Linux allows the Kernel to be configured at run time, to enable or disable different services as you see fit. This way you don’t have to compile a monolithic kernel, and can save some memory usage. Some modules you’ll only need for a short time, others you’ll need all the time. You can configure your Linux machine to load kernel modules on startup so you don’t have to remember to do that when (if) you reboot.

Module Commands

There are a few commands that allow you to maniuplate the kernel. Each is quickly described below, for more information say `man [command]`.

• depmod — handle dependency descriptions for loadable kernel modules.
• insmod — install loadable kernel module.
• lsmod — list loaded modules.
• modinfo — display information about a kernel module.
• modprobe — high level handling of loadable modules.
• rmmod — unload loadable modules.

The usage of the commands is demonstrated below, it is left as an excerise to the reader to fully understand the commands.

Using Module Commands

Below the different kernel module commands are demonstrated

# Show the module dependencies. depmod -n # Install some module insmod --autoclean [modnam] # This lists all currently loaded modules, lsmod takes no useful parameters lsmod # Display information about module eepro100 modinfo --author --description --parameters eepro100 # Removing a module (don't use the example) rmmod --all --stacks ip_tables

Module Configuration Files

The kernel modules can use two different methods of automatic loading. The first method (modules.conf) is my preferred method, but you can do as you please.

• modules.conf — This method load the modules before the rest of the services, I think before your computer chooses which runlevel to use
• rc.local — Using this method loads the modules after all other services are started

Using ‘modules.conf’ will require you to say `man 5 modules.conf`. Using ‘rc.local’ requires you to place the necessary commands (see above) in the right order.

Sample modules.conf

# modules.conf - configuration file for loading kernel modules # Create a module alias parport_lowlevel to parport_pc alias parport_lowlevel parport_pc # Alias eth0 to my eepro100 (Intel Pro 100) alias eth0 eepro100 # Execute /sbin/modprobe ip_conntrack_ftp after loading ip_tables post-install ip_tables /sbin/modprobe ip_conntrack_ftp # Execute /sbin/modprobe ip_nat_ftp after loading ip_tables post-install ip_tables /sbin/modprobe ip_nat_ftp

Sample rc.local

#!/bin/sh # # This script will be executed *after* all the other init scripts. # You can put your own initialization stuff in here if you don't # want to do the full Sys V style init stuff. /sbin/insmod ip_tables /sbin/modprobe ip_conntrack_ftp /sbin/modprobe ip_nat_ftp

Conclusion

You should see/know that modules are necessary. They can be loaded via ‘modules.conf’ or ‘rc.local’, but ‘modules.conf’ load them first and ‘rc.local’ loads them last. Using the various module commands you can add, remove, list or get information about modules.

Источник

Kernel module

Kernel modules are pieces of code that can be loaded and unloaded into the kernel upon demand. They extend the functionality of the kernel without the need to reboot the system.

To create a kernel module, you can read The Linux Kernel Module Programming Guide. A module can be configured as built-in or loadable. To dynamically load or remove a module, it has to be configured as a loadable module in the kernel configuration (the line related to the module will therefore display the letter M ).

To rebuild a kernel module automatically when a new kernel is installed, see Dynamic Kernel Module Support (DKMS).

Obtaining information

Modules are stored in /usr/lib/modules/kernel_release . You can use the command uname -r to get your current kernel release version.

Note: Module names often use underscores ( _ ) or dashes ( — ); however, those symbols are interchangeable when using the modprobe command and in configuration files in /etc/modprobe.d/ .

To show what kernel modules are currently loaded:

To show information about a module:

To list the options that are set for a loaded module:

$ systool -v -m module_name 

To display the comprehensive configuration of all the modules:

To display the configuration of a particular module:

$ modprobe -c | grep module_name 

List the dependencies of a module (or alias), including the module itself:

$ modprobe --show-depends module_name 

Automatic module loading

Today, all necessary modules loading is handled automatically by udev, so if you do not need to use any out-of-tree kernel modules, there is no need to put modules that should be loaded at boot in any configuration file. However, there are cases where you might want to load an extra module during the boot process, or blacklist another one for your computer to function properly.

systemd

Kernel modules can be explicitly listed in files under /etc/modules-load.d/ for systemd to load them during boot. Each configuration file is named in the style of /etc/modules-load.d/program.conf . Configuration files simply contain a list of kernel modules names to load, separated by newlines. Empty lines and lines whose first non-whitespace character is # or ; are ignored.

/etc/modules-load.d/virtio-net.conf

# Load virtio_net.ko at boot virtio_net

Early module loading

The initramfs image may not contain the kernel modules asked for in /etc/modules-load.d/ , it also may lack the files that have been set in that folder. Early module loading depend on the initramfs generator used:

Manual module handling

Kernel modules are handled by tools provided by kmod package. You can use these tools manually.

Note: If you have upgraded your kernel but have not yet rebooted, modprobe will fail with no error message and exit with code 1, because the path /usr/lib/modules/$(uname -r)/ no longer exists. Check manually if this path exists when modprobe failed to determine if this is the case.

# modprobe module_name 

To load a module by filename (i.e. one that is not installed in /usr/lib/modules/$(uname -r)/ ):

# modprobe -r module_name 

Setting module options

To pass a parameter to a kernel module, you can pass them manually with modprobe or assure certain parameters are always applied using a modprobe configuration file or by using the kernel command line. If the module is built into the kernel, the kernel command line must be used and other methods will not work.

Manually at load time using modprobe

The basic way to pass parameters to a module is using the modprobe command. Parameters are specified on command line using simple key=value assignments:

# modprobe module_name parameter_name=parameter_value 

Using files in /etc/modprobe.d/

Files in /etc/modprobe.d/ directory can be used to pass module settings to udev, which will use modprobe to manage the loading of the modules during system boot. Configuration files in this directory can have any name, given that they end with the .conf extension. The syntax is:

/etc/modprobe.d/myfilename.conf

options module_name parameter_name=parameter_value

Multiple module parameters are separated by spaces, in turn a parameter can receive a list of values which is separated by commas:

/etc/modprobe.d/myfilename.conf

options module_name param1=value1 param2=value2a,value2b …

# On ThinkPads, this lets the 'thinkfan' daemon control fan speed options thinkpad_acpi fan_control=1

Note: If any of the affected modules is loaded from the initramfs, then you will need to add the appropriate .conf file to FILES in mkinitcpio.conf or use the modconf hook, then regenerate the initramfs to include the .conf file. To see the contents of the default initramfs use lsinitcpio.

Using kernel command line

You can also pass options to the module using the kernel command line. This is the only working option for modules built into the kernel. For all common boot loaders, the following syntax is correct:

module_name.parameter_name=parameter_value 

thinkpad_acpi.fan_control=1

Simply add this to your bootloader’s kernel-line, as described in Kernel Parameters.

Aliasing

Aliases are alternate names for a module. For example: alias my-mod really_long_modulename means you can use modprobe my-mod instead of modprobe really_long_modulename . You can also use shell-style wildcards, so alias my-mod* really_long_modulename means that modprobe my-mod-something has the same effect. Create an alias:

alias mymod really_long_module_name

Some modules have aliases which are used to automatically load them when they are needed by an application. Disabling these aliases can prevent automatic loading but will still allow the modules to be manually loaded.

# Prevent Bluetooth autoload alias net-pf-31 off

Blacklisting

Blacklisting, in the context of kernel modules, is a mechanism to prevent the kernel module from loading. This could be useful if, for example, the associated hardware is not needed, or if loading that module causes problems: for instance there may be two kernel modules that try to control the same piece of hardware, and loading them together would result in a conflict.

Some modules are loaded as part of the initramfs. mkinitcpio -M will print out all automatically detected modules: to prevent the initramfs from loading some of those modules, blacklist them in a .conf file under /etc/modprobe.d and it shall be added in by the modconf hook during image generation. Running mkinitcpio -v will list all modules pulled in by the various hooks (e.g. filesystems hook, block hook, etc.). Remember to add that .conf file to the FILES array in /etc/mkinitcpio.conf if you do not have the modconf hook in your HOOKS array (e.g. you have deviated from the default configuration), and once you have blacklisted the modules regenerate the initramfs, and reboot afterwards.

Using files in /etc/modprobe.d/

Create a .conf file inside /etc/modprobe.d/ and append a line for each module you want to blacklist, using the blacklist keyword. If for example you want to prevent the pcspkr module from loading to avoid sounds through the PC speaker:

# Do not load the 'pcspkr' module on boot. blacklist pcspkr

Note: The blacklist command will blacklist a module so that it will not be loaded automatically, but the module may be loaded if another non-blacklisted module depends on it or if it is loaded manually.

However, there is a workaround for this behaviour; the install command instructs modprobe to run a custom command instead of inserting the module in the kernel as normal, so you can force the module to always fail loading with:

/etc/modprobe.d/blacklist.conf

. install module_name /bin/true .

This will effectively blacklist that module and any other that depends on it.

Using kernel command line

Tip: This can be very useful if a broken module makes it impossible to boot your system.

You can also blacklist modules from the bootloader.

Simply add module_blacklist=modname1,modname2,modname3 to your bootloader’s kernel line, as described in Kernel parameters.

Note: When you are blacklisting more than one module, note that they are separated by commas only. Spaces or anything else might presumably break the syntax.

Troubleshooting

Modules do not load

In case a specific module does not load and the boot log (accessible by running journalctl -b as root) says that the module is blacklisted, but the directory /etc/modprobe.d/ does not show a corresponding entry, check another modprobe source directory at /usr/lib/modprobe.d/ for blacklisting entries.

A module will not be loaded if the «vermagic» string contained within the kernel module does not match the value of the currently running kernel. If it is known that the module is compatible with the current running kernel the «vermagic» check can be ignored with modprobe —force-vermagic .

Warning: Ignoring the version checks for a kernel module can cause a kernel to crash or a system to exhibit undefined behavior due to incompatibility. Use —force-vermagic only with the utmost caution.

See also

Источник