Linux l2tp server ubuntu

L2TPServer

This configuration has been successfully tested with Android, Windows, and iOS devices.

Instructions

sudo apt-get install xl2tpd openswan ppp

IPSec / Openswan

In the /etc/ipsec.conf file copy:

config setup nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%v4:!10.152.2.0/24 #contains the networks that are allowed as subnet= for the remote client. In other words, the address ranges that may live behind a NAT router through which a client connects. oe=off protostack=netkey conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=3 rekey=no # Apple iOS doesn't send delete notify so we need dead peer detection # to detect vanishing clients dpddelay=30 dpdtimeout=120 dpdaction=clear # Set ikelifetime and keylife to same defaults windows has ikelifetime=8h keylife=1h type=transport # Replace IP address with your local IP (private, behind NAT IP is okay as well) left=x.x.x.x # For updated Windows 2000/XP clients, # to support old clients as well, use leftprotoport=17/%any leftprotoport=17/1701 right=%any rightprotoport=17/%any #force all to be nat'ed. because of iOS forceencaps=yes

Make sure you follow the setup in the ipsec.conf file, the part «config setup» and «conn l2tp-psk» should be to the very left while the other text 8 spaces to the right.

In the «/etc/ipsec.secrets» file copy:

x.x.x.x %any: PSK "somegoodpassword"

Replace x.x.x.x with your Server’s IP

Start the IPSEC service with

Please verify the IPSEC service with :

Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.28/K2.6.32-32-generic-pae (netkey) Checking for IPsec support in kernel [OK] NETKEY detected, testing for disabled ICMP send_redirects [OK] NETKEY detected, testing for disabled ICMP accept_redirects [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Checking for 'ip' command [OK] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED]

Create a file called «ipsec.vpn» in «/etc/init.d/»

case "$1" in start) echo "Starting my Ipsec VPN" iptables -t nat -A POSTROUTING -o eth0 -s 10.152.2.0/24 -j MASQUERADE echo 1 > /proc/sys/net/ipv4/ip_forward for each in /proc/sys/net/ipv4/conf/* do echo 0 > $each/accept_redirects echo 0 > $each/send_redirects done /etc/init.d/ipsec start /etc/init.d/xl2tpd start ;; stop) echo "Stopping my Ipsec VPN" iptables --table nat --flush echo 0 > /proc/sys/net/ipv4/ip_forward /etc/init.d/ipsec stop /etc/init.d/xl2tpd stop ;; restart) echo "Restarting my Ipsec VPN" iptables -t nat -A POSTROUTING -o eth0 -s 10.152.2.0/24 -j MASQUERADE echo 1 > /proc/sys/net/ipv4/ip_forward for each in /proc/sys/net/ipv4/conf/* do echo 0 > $each/accept_redirects echo 0 > $each/send_redirects done /etc/init.d/ipsec restart /etc/init.d/xl2tpd restart ;; *) echo "Usage: /etc/init.d/ipsec.vpn " exit 1 ;; esac

This will configure the firewall forwarding. If you use a local IP pool other than 10.152.2, be sure to update it.

Then set the permission to execute:

Disable the ipsec default init script with

And enable the custom one.

#update-rc.d ipsec.vpn defaults

L2TP

In the file /etc/xl2tpd/xl2tpd.conf

[global] ipsec saref = no [lns default] ip range = 10.152.2.2-10.152.2.254 local ip = 10.152.2.1 require chap = yes refuse pap = yes require authentication = yes ppp debug = yes pppoptfile = /etc/ppp/options.xl2tpd length bit = yes

• ip range = range of IP’s to give to the connecting clients
• local ip = IP of VPN server. Value must be outside of «ip range».
• refuse pap = refure pap authentication
• ppp debug = yes when testing, no when in production

Choose a good challenge-response authentication string. The secret should, ideally, be 16 characters long, and should probably be longer to ensure sufficient security. There is no minimum length requirement. In the file /etc/xl2tpd/l2tp-secrets:

* * exampleforchallengestring

In the file /etc/ppp/options.xl2tpd copy:

refuse-mschap-v2 refuse-mschap ms-dns 8.8.8.8 ms-dns 8.8.4.4 asyncmap 0 auth crtscts idle 1800 mtu 1200 mru 1200 lock hide-password local #debug name l2tpd proxyarp lcp-echo-interval 30 lcp-echo-failure 4

ms-dns option

Here you set the dns server for your lan, this dns server are pushed to the road warrior when he connects. If you wan to add several servers just add several lines.

If you need to push wins settings to the clients there is an separate option for that.

mtu / mru

On openswan.org they informs that it’s important to reduce the mru/mtu size. Because l2tp/ipsec are encapsulated several times it causes overhead, reducing this makes it possible to transmit all packages over lines with reduced mtu size.

proxyarp

Adds an entry to this system’s ARP [Address Resolution Protocol] table with the IP address of the peer and the Ethernet address of this system. This will have the effect of making the peer appear to other systems to be on the local ethernet.

name l2tpd

Is used in the ppp authentication file.

Adding Users

In the file /etc/ppp/chap-secrets copy:

user1 l2tpd chooseagoodpassword * user2 * chooseagoodpassword *

• client = username for the user
• server = the name we define in the ppp.options file for xl2tpd
• secret = password for the user
• IP Address = leave to * for any address or define addresses from were a user can login.

Note: you can add as many user you like.

Forward

Load the new settings made in /etc/sysctl.conf

Starting the VPN

sudo /etc/init.d/ipsec.vpn restart sudo /etc/init.d/xl2tpd restart

Connecting the VPN to iOS device

1. Go to Settings > General > Network > VPN > Add VPN Configuration > L2TP
2. VPN Description > the name you like
3. Set VPN server > external ip address of the VPN server (x.x.x.x)
4. Account > PPP username
5. Set password > somegoodpassword
6. Set L2TP Secret > was exampleforchallengestring
7. Connect using the PPP username/password (user1 chooseagoodpassword)

Connecting the VPN to an Android device

1. Go to Settings > Wireless & networks > VPN settings > Add VPN > Add L2TP/IPSec PSK VPN >
2. VPN Name / Description > the name you like
3. Set VPN server > external ip address of the VPN server (x.x.x.x)
4. Set IPSec pre-shared key / password > somegoodpassword
5. Enable L2TP secret > enable
6. Set L2TP Secret > was exampleforchallengestring
7. Press back, then connect using the PPP username/password (user1 chooseagoodpassword)

Debug

In case of problems this are a few commands that can help out the debugging.

sudo tcpdump -i ppp0 sudo tail -f /var/log/auth.log sudo tail -f /var/log/syslog

You can also monitor the results on the Server with

sudo tcpdump -i eth0 host aaa.bbb.ccc.ddd and not port ssh

aaa.bbb.ccc.ddd are the public IP address of your Clients

L2TPServer (последним исправлял пользователь c-50-136-58-193 2015-11-01 00:21:27)

The material on this wiki is available under a free license, see Copyright / License for details
You can contribute to this wiki, see Wiki Guide for details

Источник

Установка компонентов и настройка L2TP VPN сервера на Ubuntu Server

apt-get install strongswan

config setup virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 protostack=netkey

conn l2tpvpn type=transport authby=secret pfs=no rekey=no keyingtries=2 left=%any leftprotoport=udp/l2tp leftid=@l2tpvpnserver right=%any rightprotoport=udp/%any auto=add

%any %any : PSK "ThisPasswordKey"

Замените ThisPasswordKey на сгенерированный Вами ключ, подключение разрешено с любого IP.

Установка и настройка L2TP

[global] port = 1701 access control = no ipsec saref = yes force userspace = yes auth file = /etc/ppp/chap-secrets [lns default] ip range = 176.16.10.10-176.16.10.200 local ip = 176.16.10.1 name = l2tpserver pppoptfile = /etc/ppp/options.xl2tpd flow bit = yes exclusive = no hidden bit = no length bit = yes require authentication = yes require chap = yes refuse pap = yes

Настройка PPP

noccp auth crtscts mtu 1410 mru 1410 nodefaultroute lock noproxyarp silent modem asyncmap 0 hide-password require-mschap-v2 ms-dns 8.8.8.8 ms-dns 8.8.4.4

"vpnuser" l2tpserver "vpnuserpassword" "172.16.10.10" "vpnuser2" l2tpserver "vpnuserpassword2" *

Для пользователя vpnuser указан локальный IP-адрес, который он будет получать от сервера при подключении. Пользователь же vpnuser2 будет получать IP-адрес автоматически. Перезапустим xl2tpd:

Источник