How to access localhost of linux subsystem from windows
I am using windows 10 and I have ubuntu 16.04 installed as linux subsystem. I am running a rails app on port 4567, which I want to access from windows. I know an approach of using ip address, but ifconfig didn’t work. (I tried running /sbin/ifconfig ). This outputs a warning as, Warning: cannot open /proc/net/dev (No such file or directory). Limited output. I searched in internet, came across this open issue. So is there any alternative feasible solution?
1. The Ubuntu on Windows is based on 14.04. 2. You could simply use a VM. It’s easier to setup, probably has a GUI (if you want one) and supports all the features you need.
6 Answers 6
The answer to this is surprisingly simple which is why searching isn’t giving you the right results.
All that WSL does is provide a translation layer between the Linux apps and the windows kernel, very much like how Wine works on Linux. Because of this some core parts of the Ubuntu system are just not there, networking being one of them. WSL translates the Linux system calls into windows ones so the Ubuntu network data flows through the exact same TCP/IP stack as the windows data.
In short this means to access the Linux localhost you just access the windows one, they are the same. localhost:4567 or 127.0.0.1:4567 will do what you want.
As an aside I’ve been using rails on WSL, it seems to work perfectly except the swing and listen gems don’t play well, I had to disable them.
It does work 🙂 Installed Ubuntu, Nginx on it, started Nginx and now I can open localhost on windows 🙂 Thanks
I needed to access my WSL-hosted port from another device in my LAN
(e.g. for mobile development), and I found @Owen Tourlamain’s answer of didn’t help for that.
I needed to set up portproxy , and I found that using connectaddress=localhost or connectaddress=127.0.0.1 did not work for me (WSL2, Windows 10 20H2).
So I still needed the answer the the OP’s question, and it turns out it’s surprisingly simple:
Note:
You have to trim whitespace if you’re using it inline in a powershell command, e.g.:
netsh interface portproxy add v4tov4 listenport=19000 listenaddress=0.0.0.0 ` connectport=19000 connectaddress=$($(wsl hostname -I).Trim()); Accessing WSL from your network
The OP asked about accessing WSL «from windows». If you want to also access it «from your private network», you’ll also need to, one time, make a firewall rule allowing a specific port (or range of ports).
⚠️ Warning: Do not turn Windows firewall «off». Make a rule to open only specific ports that you need.
New-NetFireWallRule -Profile Private -DisplayName 'MyRule ports for LAN development' ` -Direction Inbound -LocalPort 19000-19006 -Action Allow -Protocol TCP - -LocalPort 19000-19006 ← Replace the 19000-19006 with the port(s) you need.
- -Profile Private so that the ports are only open a network that you’ve marked as being «Private»
- -Direction Inbound means inbound (ingress) only
- -DisplayName ‘MyRuleName blah blah. ‘ is for you, human-readable name. But pick something you’ll remember, because you can use this name to find the rule in the future, to view its status or to delete it. e.g. Get-NetFirewallRule | Where-Object
Old question that was bumped today via another answer, so I’ll chime in. This question was originally asked for WSL1. While the «answer» is the same for WSL2, there are some slight differences that need to be addressed.
First, on WSL1, as the original accepted answer from 2016 mentions, the network is really running on the Windows host interface. That’s why localhost / 127.0.0.1 (or the address of the Windows NIC) works there.
WSL2, on the other hand, runs virtualized, so the network interface is a vNIC with a different address than that of the Windows host. That network is actually NAT’d behind the Windows host. This is also why you can access a WSL1 instance using the Windows IP address from another machine on the network, but no so with WSL2.
But WSL2 does have a feature known as «localhost forwarding», which makes it work like WSL1 for localhost / 127.0.0.1 . This feature is turned on by default, but can be disabled (although I don’t know of any reason for ever doing so, honestly).
This feature allows you to access a service (like a Rails app, in this question). If the port isn’t in use on the Windows NIC, then WSL2 will auto-forward the localhost request to the same port on the WSL2 vNIC.
So all is well and good, and you can access both WSL1 and WSL2 services via localhost , right?
Not so fast, unfortunately. Sometimes, as two other answers have mentioned, localhostForwarding «breaks». We’ve identified two very common (and related) use-cases where this will happen:
- When the host Windows is hibernated.
- When the host Windows is powered on using Windows «Fast Startup» feature, which turns out to be enabled by default. This feature uses a form of hibernation.
- Don’t hibernate if possible
- Turn off Fast Startup. You’ll find it in the Control Panel. Navigate to Hardware and Sound ->Power Options ->Change what the Power Buttons do
- If you do find yourself in a situation where the feature is not working, as @AhmetK’s answer mentioned, you can typically recover localhost forwarding by:
- Exiting all running WSL instances
- Issuing wsl —shutdown (from PowerShell, CMD, or even the Start Menu). While a full Windows restart will have the same effect, a wsl —shutdown is much faster.
- Restart your WSL instance and running services/apps.
Reference the comments on this SO answer which have confirmed the issue and solution.