Moxa uport 1110 linux

Saved searches

Use saved searches to filter your results more quickly

You signed in with another tab or window. Reload to refresh your session. You signed out in another tab or window. Reload to refresh your session. You switched accounts on another tab or window. Reload to refresh your session.

Moxa-Linux/mxu11x0

This commit does not belong to any branch on this repository, and may belong to a fork outside of the repository.

Name already in use

A tag already exists with the provided branch name. Many Git commands accept both tag and branch names, so creating this branch may cause unexpected behavior. Are you sure you want to create this branch?

Sign In Required

Please sign in to use Codespaces.

Launching GitHub Desktop

If nothing happens, download GitHub Desktop and try again.

Launching GitHub Desktop

If nothing happens, download GitHub Desktop and try again.

Launching Xcode

If nothing happens, download Xcode and try again.

Launching Visual Studio Code

Your codespace will open once ready.

There was a problem preparing your codespace, please try again.

Latest commit

Git stats

Files

Failed to load latest commit information.

readme.txt

============================================================================= MOXA UPort 11x0 USB to Serial Hub Family Driver Installation Guide for Linux Kernel 4.x Copyright (C) 2019, Moxa Inc. ============================================================================= Date: 08/19/2020 CONTENTS 0. Note 1. Introduction 2. System Requirements 3. Installation 3.1 Driver files 3.2 Device naming convention 3.3 Module driver configuration 3.4 Static driver configuration 3.5 Verify driver installation 4. Uninstallation 5. Setserial 6. Troubleshooting ----------------------------------------------------------------------------- 0. Note The Moxa UPort 11x0 USB to Serial Hub driver can be used in the Linux kernel with the usbcore and usbserial modules. This two modules is built-in module in the Linux kernel version 2.6.x and follow. In the Linux kernel version, you must check this two build-in modules existed. Otherwise, you will fail to using MOXA UPort 11x0 USB to Serial Hub driver. ----------------------------------------------------------------------------- 1. Introduction The MOXA UPort 11x0 USB to Serial Hub Linux driver supports following devices. - UPort 1110, 1 port RS-232 USB to Serial Hub. - UPort 1130, 1 port RS-422/485 USB to Serial Hub. - UPort 1130I, 1 port RS-422/485 USB to Serial Hub with isolation protection. - UPort 1150, 1 port RS-232/422/485 USB to Serial Hub. - UPort 1150I, 1 port RS-232/422/485 USB to Serial Hub with isolation protection. - USB Console, 1 port RS-232 USB to Serial Hub. - USB-to-Serial Port Driver, 1 port RS-232/422/485 USB to Serial Hub This driver supports x86 and x64(AMD64/EM64T) hardware platform. In order to maintain compatibility, this version has also been properly tested with several Linux distribution (see version.txt). However, if compatibility problem occurs, please contact Moxa Technologies technical support. (support@moxa.com) All the drivers are published in form of source code under GNU General Public License in this version. Please refer to GNU General Public License announcement in each source code file for more detail. This version of driver can be only installed as Loadable Module (Module driver). Before you install the driver, please refer to hardware installation procedure in the User's Manual. ----------------------------------------------------------------------------- 2. System Requirements - Hardware platform: x86, x64 - Kernel version: 2.6.x and above - gcc version 3.x - kernel source Additional requirements for Raspbian - gcc-4.8.3 or above - ncurses-devel-5.9 or above - rpi-source, read the instruction from it's website. (https://github.com/notro/rpi-source/wiki) Note: - rpi-source is a 3rd party package offering integrated kernel resouce for building driver. Real TTY are tested with this package and working well. However the requirements may be various for different Raspbian version. Please read the manual of Raspbian and rpi-source to understand the knowhow and limitation. - Real TTY driver with Raspbian Jessie(4.4.50) and Buster(4.19) are tested on Pi 2/3. ----------------------------------------------------------------------------- 3. Installation 3.1 Driver files 3.2 Device naming convention 3.3 Module driver configuration 3.4 Static driver configuration 3.5 Verify driver installation 3.1 Driver files The driver file may be obtained from website, under the product page. The first step is to copy driver file "driv_linux_uport1p_[VERSION]_[BUILD].tgz" into a user directory. e.g. /moxa. Please execute commands as below. # cd /moxa # tar xvfz driv_linux_uport1p_[VERSION]_[BUILD].tgz 3.2 Device naming convention You may find all the driver files in //mxu11x0/. Following installation procedure depends on the model you'd like to run the driver. Dialin and callout port ----------------------- This driver remains traditional serial device properties. Because the limitation of the usb build-in modules that are usbcore and usbserial, There is only one special file name for each serial port. This one is dial-in port which is named "ttyUSBxx". 3.3 Module driver configuration To simplify the processes behind, we provide a single step to build, install and load the MOXA driver. You may execute the ./mxinstall to use the MOXA product. Once you successfully execute ./mxinstall, you can skip step 3.3.1 and 3.3.2. 3.3.1 Build the MOXA driver Before using the MOXA driver, you need compile the all the source code. This step is only need to be executed once. But you still re-compile the source code if you modify the source code. Find "Makefile" in /moxa/mxu11x0/driver, then run # make clean; make install The driver files "mxu11x0.ko" will be properly compiled and copied to system directories respectively. 3.3.2 Load the MOXA driver The driver will be loaded automatically while pluging the UPort into you PC. Besides, you can load the driver manually. # modprobe mxu11x0 It will activate the module driver. You may run "lsmod" to check if "mxu11x0" is activated. Before you load this module driver, you have to run "lsmod" to check if "usbcore" and "usbserial" are activated. 3.4 Static driver configuration Note: To use static driver, you must install the linux kernel source package. 3.4.1 Create link # cd /usr/src//drivers/usb/serial/ # ln -s /moxa/mxu11x0/driver/mxu11x0.c mxu11x0.c # ln -s /moxa/mxu11x0/driver/mxu11x0.h mxu11x0.h # ln -s /moxa/mxu11x0/driver/mxu1110_fw.h mxu1110_fw.h # ln -s /moxa/mxu11x0/driver/mxu1130_fw.h mxu1130_fw.h # ln -s /moxa/mxu11x0/driver/mxu1131_fw.h mxu1131_fw.h # ln -s /moxa/mxu11x0/driver/mxu1150_fw.h mxu1150_fw.h # ln -s /moxa/mxu11x0/driver/mxu1151_fw.h mxu1151_fw.h # ln -s /moxa/mxu11x0/driver/mxu3001_fw.h mxu3001_fw.h # ln -s /moxa/mxu11x0/driver/mxu7001_fw.h mxu7001_fw.h 3.4.2 Modify kernel configuration file. Add the following line into configuration file. /usr/src//drivers/usb/serial/Kconfig . config USB_SERIAL_CONSOLE . config USB_SERIAL_GENERIC . config MOXA_UPORT_11X0 <-- Add the lines. tristate "USB Moxa UPort 11x0 Driver" <-- depends on USB_SERIAL <-- . 3.4.3 Modify the kernel Makefile Add the following line to the last line of Makefile. /usr/src//drviers/usb/serial/Makefile . . . obj-$(CONFIG_MOXA_UPORT_11X0) += mxu11x0.o <-- Add the line. 3.4.4 Setup kernel configuration Configure the kernel: # cd /usr/src/# make menuconfig You will go into a menu-driven system. Please select [Device Drivers] [USB Support], [USB Serial Converter support], enable both the [USB Serial Converter support] and the [USB MOXA UPORT 11x0 Driver] drivers with "[*]" by pressing space bar for built-in (not "[M]"), then select [Exit] to exit this program and save kernel configurations. 3.4.5 Rebuild kernel The following are for Linux kernel rebuilding, for your reference only. For appropriate details, please refer to the Linux document. a. cd /usr/src/ b. make c. make modules d. make modules_install e. make install 3.5 Verify driver installation You may refer to /var/log/syslog to check the latest status log reported by this driver whenever it's activated or type command "dmesg" to get driver information. ----------------------------------------------------------------------------- 4. Uninstallation # cd /moxa/mxu11x0 # make remove ----------------------------------------------------------------------------- 5. Setserial NOTE: To use the setserial tools, you have to install it first. The setserial is a free software, you can download it on http://sourceforge.net/projects/setserial/ . MOXA UPort 1130/1130I provides three interfaces(RS-485 2W, RS-485 4W, RS-422) and UPort 1150/1150I/USB-to-Serial Port Driver provides four interfaces (RS-232, RS-485 2W, RS-485 4W, RS-422). If you want to switch different interface, you can execute the setserial command to set the port's interface. The supported parameter is listed below. parameter value interface port 0 RS-232 1 RS-485 2W 2 RS-422 3 RS-485 4W For example: To set the port's informations: # setserial /dev/ttyUSB0 port 1 To get the port's informations: # setserial -G /dev/ttyUSB0 ----------------------------------------------------------------------------- 6. Limitation 1. Max. ports If you want to install more than one UPort USB serial Hub, the best way is to connect to USB port directly. In lab test, four USB ports with four UPorts still work very well. If we connect to USB hub, the throughput will be dropped down. To get good performance, please connecting UPort to USB host directly . 2. Compile error To build Moxa driver, it needs kernel header files. If you got some compile error, please run "rpm -qa | grep kernel" to check whether the kernel-source package is installed properly. If not, please get the kernel-source irpm package and run "rpm -ivh " to install. For Ubuntu and Debian, if there is no rpm in your system, try the following commands to install kernel headers: # apt-get install linux-headers-$(uname -r) You also need to make sure the build tool is ready, including make/gcc/lib. Take Ubuntu and Debian for example, type the commands below to install GNU GCC: # apt-get install build-essential Please see Linux relevant document to get more information. 3. Probe error The UPort 11x0 series USB to Serial Hub need firmware downloaded after attaching to PC. Hence, the driver will reset the UPort after downloading firmware and probe the UPort again. After that, the UPort will attach to the /dev/ttyUSBxx. Therefore, the message "mxusb:probe of x-x:x.x failed with error -5" will show only once before successfully installing the device. You may refer to /dev/ttyUSBxx to see if the UPort is set correctly. -----------------------------------------------------------------------------

Источник

UPort 1110 MOXA

Востребованный однопортовый конвертер MOXA UPort 1110 используют для диагностики и отладки промышленных сетей, а также для обновления программного обеспечения последовательных устройств, оснащенных портом RS-232. Универсальный преобразователь подходит для работы с системами автоматизации в различных отраслях промышленности. Конвертер UPort 1110 позволяет подключить оборудование к ПК или ноутбуку, не прекращая работу системы.

Пользоваться MOXA UPort 1110 просто и удобно. Для начала работы достаточно установить драйверы на компьютер и подключить оборудование. Необходимое ПО поставляется вместе с устройством.

Долговечный и надежный преобразователь UPort 1110 от проверенного производителя MOXA обеспечивает быструю бесперебойную передачу данных в любой ситуации.

1-портовый конвертер USB в RS-232 MOXA UPort 1110 позволяет подключить одно устройство, работающее по интерфейсу RS-232, к компьютеру или ноутбуку через USB порт. Его применение очень удобно для мобильных и инструментальных приложений, а так же подключения компьютеров, у которых отсутствует последовательный порт.
USB порт и технология plug & play значительно упрощают установку последовательного порта в систему. Конвертеры MOXA UPort 1110 не требуют дополнительных ресурсов системы, таких как IRQ, DMA, или адресное пространство ввода-вывода. Пользователю не нужно открывать корпус компьютера и останавливать работу системы, для того чтобы добавить последовательный порт.

Как и все остальные устройства MOXA, конвертеры UPort 1110 поставляются с удобным программным обеспечением, которое поддерживает семейство ОС Windows и Linux. Специальная утилита отображает номера COM портов устройства MOXA UPort 1110, которые присваиваются конвертерам в системном трее.

Источник

Как настроить преобразователь UPort?

Для начала работы необходимо установить драйвер. Сразу после установки драйвера преобразователь готов к работе. Все настройки преобразователя в ОС Windows осуществляются через Диспетчер устройств. В разделе Многопортовые последовательные адаптеры (Multiport serial adapters) можно изменить интерфейс последовательного порта (RS-232, RS-422, RS-485), режим передачи данных. В разделе Порты (COM и LTP) можно изменить параметры передачи данных по COM-порту.

Рекомендованные продукты

Источник

Какие ОС поддерживает UPort 1110/1130/1150?

Windows 95/98/ME/NT/2000 Windows Server 2008/2012/2016/2019 Windows XP/2003/Vista/2008/7/8/8.1/10 (x86/x64) Windows Embedded CE 5.0/6.0 Linux 2.4.x, 2.6.x, 3.x, 4.x, 5.x MacOS 10.12, 10.13, 10.14, 10.15 Android Последнюю версию драйверов виртуального COM-порта можно скачать с сайта www.moxa.com.

Рекомендованные продукты

Недавно просмотренные

Все материалы, характеристики, цены представленные на сайте не являются публичной офертой.
Оплата принимается в рублях по курсу ЦБ РФ на день оплаты

© 2023 MOXA.pro - Решения MOXA для профессионалов в промышленных коммуникациях

Сайт официального дистрибьютора MOXA Inc. в России. Данный веб-сайт не имеет отношения к компании Moxa Inc. или её представительствам. MOXA является зарегистрированным товарным знаком компании Moxa Inc.

© 2023 MOXA.pro - Решения MOXA для профессионалов в промышленных коммуникациях

Источник