How to disable IPv6 on Linux
Question: I notice that one of my applications is trying to establish a connection over IPv6. But since our local network is not able to route IPv6 traffic, the IPv6 connection times out, and the application falls back to IPv4, which causes unnecessary delay. As I don’t have any need for IPv6 at the moment, I would like to disable IPv6 on my Linux box. What is a proper way to turn off IPv6 on Linux?
IPv6 has been introduced as a replacement of IPv4, the traditional 32-bit address space used in the Internet, to solve the imminent exhaustion of available IPv4 address space. However, since IPv4 has been used by every host or device connected to the Internet, it is practically impossible to switch every one of them to IPv6 overnight. Numerous IPv4 to IPv6 transition mechanisms (e.g., dual IP stack, tunneling, proxying) have been proposed to facilitate the adoption of IPv6, and many applications are being rewritten, as we speak, to add support for IPv6. One thing for sure is that IPv4 and IPv6 will inevitably coexist for the forseeable future.
Ideally the ongoing IPv6 transition process should not be visible to end users, but the mixed IPv4/IPv6 environment might sometimes cause you to encounter various hiccups originating from unintended interaction between IPv4 and IPv6. For example, you may experience timeouts from applications such as apt-get or ssh trying to unsuccessfully connecting via IPv6, DNS server accidentally dropping AAAA DNS records for IPv6, or your IPv6-capable device not compatible with your ISP’s legacy IPv4 network, etc.
Of course this doesn’t mean that you should blindly disable IPv6 on you Linux box. With all the benefits promised by IPv6 (e.g., more efficient routing, simpler network configuration), we as a society want to fully embrace it eventually, but as part of troubleshooting process for end-user experienced hiccups, you may try turning off IPv6 to see if indeed IPv6 is a culprit.
Here are a few techniques allowing you to disable IPv6 partially (e.g., for a certain network interface) or completely on Linux. These tips should be applicable to all major Linux distributions including Ubuntu, Debian, Linux Mint, CentOS, Fedora, RHEL, and Arch Linux.
Check if IPv6 is Enabled on Linux
All modern Linux distributions have IPv6 automatically enabled by default. To see IPv6 is activated on your Linux, use ifconfig or ip commands. If you see inet6 in the output of these commands, this means your Linux has IPv6 enabled.
Disable IPv6 Temporarily
If you want to turn off IPv6 temporarily on your Linux system, you can use /proc file system. By temporarily, I mean that the change you make to disable IPv6 will not be preserved across reboots. IPv6 will be enabled back again after you reboot your Linux box.
To disable IPv6 for a particular network interface, use the following command.
$ sudo sh -c 'echo 1 > /proc/sys/net/ipv6/conf//disable_ipv6'
For example, to disable IPv6 for eth0 interface:
$ sudo sh -c 'echo 1 > /proc/sys/net/ipv6/conf/eth0/disable_ipv6'
To re-enable IPv6 back on eth0 interface:
$ sudo sh -c 'echo 0 > /proc/sys/net/ipv6/conf/eth0/disable_ipv6'
If you want to disable IPv6 system-wide for all interfaces including loopback interface, use this command:
$ sudo sh -c 'echo 1 > /proc/sys/net/ipv6/conf/all/disable_ipv6'
Disable IPv6 Permanently across Reboots
The above method does not permanently disable IPv6 across reboots. IPv6 will be activated again once you reboot your system. If you want to turn off IPv6 for good, there are several ways you can do it.
Method One
The first method is to apply the above /proc changes persistently in /etc/sysctl.conf file. That is, open /etc/sysctl.conf with a text editor, and add the following lines.
# to disable IPv6 on all interfaces system wide net.ipv6.conf.all.disable_ipv6 = 1 # to disable IPv6 on a specific interface (e.g., eth0, lo) net.ipv6.conf.lo.disable_ipv6 = 1 net.ipv6.conf.eth0.disable_ipv6 = 1
To activate these changes in /etc/sysctl.conf , run:
$ sudo sysctl -p /etc/sysctl.conf
Method Two
An alternative way to disable IPv6 permanently is to pass a necessary kernel parameter via GRUB/GRUB2 during boot time.
Open /etc/default/grub with a text editor, and add ipv6.disable=1 to GRUB_CMDLINE_LINUX variable.
GRUB_CMDLINE_LINUX="xxxxx ipv6.disable=1"
In the above, xxxxx denotes any existing kernel parameter(s). Add ipv6.disable=1 after them.
Finally, don’t forget to apply the modified GRUB/GRUB2 settings by running:
On Debian, Ubuntu or Linux Mint:
$ sudo grub2-mkconfig -o /boot/grub2/grub.cfg
Now IPv6 will be completely disabled once you reboot your Linux system.
Other Optional Steps after Disabling IPv6
Here are a few optional steps you can consider after disabling IPv6. This is because while you disable IPv6 in the kernel, other programs may still try to use IPv6. In most cases, such application behaviors will not break things, but you want to disable IPv6 for them for efficiency or safety reason.
1. /etc/hosts
Depending on your setup, /etc/hosts may contain one or more IPv6 hosts and their addresses. Open /etc/hosts with a text editor, and comment out all lines which contain IPv6 hosts.
# comment these IPv6 hosts # ::1 ip6-localhost ip6-loopback # fe00::0 ip6-localnet # ff00::0 ip6-mcastprefix # ff02::1 ip6-allnodes # ff02::2 ip6-allrouters
2. Network Manager
If you are using Network Manager to manage your network settings, you can disable IPv6 on Network Manager as follows. On Network Manager, open the wired connection for which you want to disable IPv6, click on IPv6 Settings tab, and choose Ignore in Method field. Save the change and exit.
3. SSH server
By default, OpenSSH server ( sshd ) tries to bind on both IPv4 and IPv6 addresses. To force sshd to bind only on IPv4 address, open /etc/ssh/sshd_config with a text editor, and add the following line. inet is for IPv4 only, and inet6 is for IPv6 only.
$ sudo vi /etc/ssh/sshd_config
Support Xmodulo
This website is made possible by minimal ads and your gracious donation via PayPal or credit card
Please note that this article is published by Xmodulo.com under a Creative Commons Attribution-ShareAlike 3.0 Unported License. If you would like to use the whole or any part of this article, you need to cite this web page at Xmodulo.com as the original source.
Arch Linux
I’ve been trying to disable IPV6 as I think it is making my connection slow. I have looked at the arch wiki (https://wiki.archlinux.org/index.php/IPv6#Disable_IPv6) for how to do this and it recommends adding a few lines to /etc/sysctl.d/40-ipv6.conf. The problem that I have is that that file is missing and when I add I create it and the recommended lines, I still get an IPV6 address. I have added these lines to it:
net.ipv6.conf.all.disable_ipv6 = 1
net.ipv6.conf.lo.disable_ipv6 = 1
net.ipv6.conf.enp1s0f0.disable_ipv6 = 1
The output from ifconfig looks like this:
enp3s0: flags=4163 mtu 1500
inet 192.168.1.180 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::7e7f:c4a0:f2b1:b023 prefixlen 64 scopeid 0x20
inet6 2a00:23c4:891b:8201:b95d:ff9f:4df1:cdd6 prefixlen 64 scopeid 0x0
ether fc:aa:14:0d:9a:39 txqueuelen 1000 (Ethernet)
RX packets 6697 bytes 3038492 (2.8 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 6200 bytes 725617 (708.6 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73 mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
loop txqueuelen 1000 (Local Loopback)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
I don’t know really know where I’m going wrong, but if someone could explain that would be great. (Also I am using i3-gaps but I don’t think that’s relevant apart from the fact its sort of difficult to use the nm-applet)
Last edited by Liiht (2019-04-13 16:08:27)