Tenda FH303 review
The Tenda FH303 (FH303) router released in 2013. It is powered by Broadcom BCM5357C0 @ 300 MHz chipset, 32 MB of RAM and 4 MB of flash. The N300 router is compatible with IEEE 802.11b/g/n standards, and the maximum speed that you can get with FH303 is 300 Mbps. The router has 1 x 10/100 Mbps WAN and 3 x 10/100 Mbps LAN ports.
The FH303 is an affordable and reliable router designed for basic networking needs. Tenda is a reputable manufacturer in the networking industry known for providing a wide range of networking devices.
Tenda FH303 (FH303) specifications
Body
The dimensions and design of a router can impact its cooling capabilities. Routers with larger dimensions may have more space for internal cooling mechanisms, such as larger fans or heat sinks, which can help dissipate heat more effectively.
System
The Tenda FH303 router is equipped with Broadcom BCM5357C0 @ 300 MHz processor. The FH303 has 32 MB of RAM. Some advanced router features and software functionalities require a certain amount of RAM to operate properly. For example, routers with more RAM can support advanced security features, VPN services, or QoS (Quality of Service) prioritization more effectively. The FH303 has 4 MB of flash memory. A larger flash memory allows for more storage space to accommodate future firmware upgrades.
The process of upgrading the firmware on routers has become relatively simple and user-friendly over the years. The Tenda provides easy-to-use interfaces and instructions to guide users through the firmware upgrade process. The Tenda FH303 router comes with 9 V / 1 A PSU. This unit is responsible for providing electrical power to the router, and if it becomes faulty, it can be replaced with a new, compatible one.
Network
The FH303 router offers built-in security features to protect your network and connected devices. The IPv4 is the fourth iteration of the Internet Protocol (IP) and is the most widely used version of IP on the internet today. The Tenda FH303 has 3 x 10/100 Mbps LAN and 1 x 10/100 Mbps WAN ports. LAN or Ethernet ports (RJ-45) are used to connect devices to the local area network (LAN). WAN ports often require specific configuration settings based on the type of internet connection provided by your ISP. The WAN port on the FH303 router is a Fast Ethernet port, not a Gigabit Ethernet. The Fast Ethernet ports are capable of supporting speeds up to 100 Mbps, which is still suitable for most internet connections.
Wireless
| Antennas | 3 x 5 dBi fixed |
|---|---|
| 2.4 GHz | yes |
| 5 GHz | no |
| 60 GHz | no |
| Standards | IEEE 802.11b/g/n |
| Class | N300 |
| Speed | 300 Mbps |
| Transmit power | 20 dBm |
| Security | WEP WPA WPA2 WPS |
| Guest network | no |
This router has 3 x 5 dBi, fixed antennas. Antennas play a significant role in Wi-Fi performance and coverage. They are essential components of wireless routers that transmit and receive radio signals to establish wireless connections with devices. This router is 2.4 GHz capable. The 2.4GHz band refers to the portion of the radio spectrum between 2.400 and 2.4835 gigahertz. This frequency range is unlicensed and globally available for various wireless applications, including Wi-Fi.
The FH303 is a Wi-Fi 4 (802.11n) router. Wi-Fi 4 improved the range and coverage compared to previous Wi-Fi standards. The use of MIMO technology and other enhancements help to mitigate signal degradation and provide better coverage in larger homes or office environments. This allows devices to maintain a stable connection even when located farther away from the Wi-Fi router. The N300 refers to the maximum combined data transfer rate supported by the router across all Wi-Fi bands.
The FH303 is capable of a maximum throughput speed of 300 Mbps. The real-world speed of a FH303 router is typically lower than its theoretical maximum speed. The TX power (20 dBm) of a router refers to the transmission power or signal strength at which the router broadcasts its Wi-Fi signal. It determines the range and coverage area of the wireless network. The FH303 router offers several security protocols: WEP, WPA, WPA2, WPS.
The WEP (Wired Equivalent Privacy) was the first security protocol for Wi-Fi networks but is now considered weak and easily compromised. It uses a static encryption key and has known vulnerabilities, so it is no longer recommended for securing Wi-Fi networks. The WPA2 (Wi-Fi Protected Access 2) was introduced as an improvement over WEP and provides stronger security. If WPA3 is not available, WPA2-Personal with AES encryption is still considered secure. The FH303 router offers WPS. The WPS (Wi-Fi Protected Setup) provides a simplified and convenient method for connecting devices to a Wi-Fi network. Instead of manually entering the Wi-Fi network name (SSID) and password, users can use the WPS feature to establish a connection with the push of a button or by entering a PIN.
Connectivity
The FH303 router doesn’t have file-server or print-server functionality.
Administration
The default IP addresses of the Tenda FH303 device is 192.168.0.1. These address allows you to access the router’s console login page. If you are unable to log in to the setup panel of your Tenda router, performing a reset can be a helpful troubleshooting step. It is highly recommended to change the default password of your FH303 router after the initial setup. If you forget the new password in the future, you may need to perform a factory reset on the router to revert to the default settings.
The specifications above are based on the official data published by the manufacturer, but we also take user reviews into consideration. If you found an error or something lacking in the specifications above for the Tenda FH303, then don’t hesite and signal the problem to us.
Tenda FH303 (FH303) pictures
Tenda FH303 (FH303) comparisons
According to our statistics, the Tenda FH303 router was most often compared on our site with the following routers.
If there’s information about the Tenda FH303 that you would like to see on this site, then write to our webmaster@routerchart.com address.
Tenda FH303
Перед приобретением Tenda FH303 по самой низкой цене, изучите характеристики, видео обзоры, плюсы и минусы модели, отзывы покупателей.
Характеристики Tenda FH303
Основные характеристики *
| Тип связи | Wi-Fi |
| Тип устройства | точка доступа |
| Встроенная поддержка 3G (UMTS) | Нет |
| Встроенная поддержка WiMAX | Нет |
| Встроенная поддержка LTE | Нет |
| Встроенная поддержка LTE Advanced | Нет |
| ADSL2+ | Нет |
| Стандарт Wi-Fi | 802.11n |
| Частотный диапазон устройств Wi-Fi | 2.4 ГГц |
| Одновременная работа в двух диапазонах | Нет |
| Макс. скорость беспроводного соединения | 300 Мбит/с |
| MIMO | Нет |
| Поддержка L2TP | Есть |
| Поддержка PPTP | Есть |
| Поддержка IEEE 802.1q (VLAN) | Нет |
| Поддержка IPv6 | Нет |
| Автономность | Нет |
Опции точки доступа/моста *
| Web-сервер | Нет |
| Число портов коммутатора | 3 |
| Режим репитера (повторителя) | Есть |
| Подключение web-камеры | Нет |
| Гостевая сеть | Есть |
| UPnP AV-сервер | Нет |
| Скачивание файлов | Нет |
| Скорость портов коммутатора | 100 Мбит/сек |
| Файловый сервер | Нет |
| FTP-сервер | Нет |
| Режим моста | Есть |
Маршрутизатор *
| DHCP-сервер | Есть |
| Демилитаризованная зона (DMZ) | Есть |
| NAT | Нет |
| SPI | Нет |
| Встроенный межсетевой экран | Нет |
| WDS | Есть |
| Dynamic DNS | Есть |
| Маршрутизатор | Есть |
| Статическая маршрутизация | Есть |
Дополнительная информация *
| Возможность подключения 3G-модема | Нет |
| Power over Ethernet | Нет |
| Возможность подключения WiMAX-модема | Нет |
| Установка вне помещения | Нет |
| Возможность подключения LTE-модема | Нет |
* Точные параметры уточняйте на сайте продавца.
FH303-How to setup the router for PPPOE internet connection mode
setup the router for PPPOE mode and the steps are as below.
Note : if you have no idea about the internet connection type and the accounts please call
Connect the modem with the WAN port of the router, and then connect your computer with
one of the LAN ports of the router by a cable.
Note: After connection the SYS light should be blinking, the WLAN light should be on or
blinking, the WAN light should be on or blinking.
1 Click Network Connection Icon on the system tray, then click Open Network and Sharing
Center. (Here is for windows 7, other operating system please click HERE .)
2 Click on Change adapter settings.
3 Right click Local Area Connection, then choose Properties option.
4 Double click on Internet Protocol Version 4(TCP/IPv4)
5 Choose Obtain an IP address automatically and Obtain DNS server address
automatically and then click OK.
6 Also click OK on the first Local Connection Properties window
1 Open a browser then type 192.168.0.1 in address bar, click Enter.
Note : if you cannot login the home page, please click HERE .
2 Fill in admin in the Password field, click OK to login.
3 Choose the PPPOE option, then type the ISP Username and ISP Password in the correct
bars, then set a 2.4G Security as you want, click OK to save the settings, then click
Advanced to login the advanced setting page.
Note : the Security Key should be at least 8 characters.
4 Click on Tools, then click on Reboot, and then press the Reboot The Router button to
reboot the router for refreshing the device info.
Type the User Name and Password as admin then Click on Advanced to login the advances
setting page, and then check on the Status if the Connection Status shows Connected
that means you can access internet, please check.